SILENT KNIGHT 4720 Manual de instalación Pagina 10
- Pagina / 82
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Regency
®
Model 4724 Control Expander Installation Manual (P/N 150596-02, Rev. A) Revised 8/98
2
Section 2: UL Requirements
1. The RINGBACK @ CLOSE option must be selected for all commercial burglary applica-
tions.
2. The audible alarm must be placed where it can be heard by all partitions. A fire audible
alarm device shall be installed indoors in accordance with NFPA 74 and 72 Proprietary
Protective Signaling Systems. This may result in separate audible alarms, for fire and bur-
glary alarm signals.
NOTE An indoor/outdoor signaling device can be used if it gives different signals for fire and bur-
glary alarms.
3. For commercial burglary alarm units, the audible device must be installed where the audi-
ble test (BELL TEST @ ARM) can be heard by all system users in all partitions. If off
premises transmissions are used, the audible device can be installed inside the protected
premises.
4. For commercial burglary alarm units, the control panel and the audible device power sup-
ply must be protected by a 24 hour tamper switch and a lined housing, or they must be
enclosed in a protected area that is armed 24 hours a day. The tamper switches or pro-
tected area must be programmed as “not bypassable.”
5. For UL approved installations, the Regency Supervised Siren Module must be wired to the
4724. To warn of a fire, the module provides a UL temporal-three siren that uses three dis-
tinctive, repeating short beeps. The module converts the panel’s non-supervised, steady
fire cadence to a supervised, temporal-three fire cadence. This module also provides a dis-
tinctive supervised burglary (police) siren. See Figure 1 for details on wiring the module
to the 4724. For additional information, see the Regency Supervised Siren Module Instal-
lation Instructions (P/N 466-1584).
6. The 4724 is intended to be used for coverage under one management, one ownership, and
one address divided into separately armed, partitions (zones) of coverage.
Figure 1: Connecting the Supervised Siren Module to the 4724
8457G30B.DSF
FIRE
4.7k Ohm
EOL RESISTOR 49-365
(LOCATE AT SIREN)
1
COM
2
4
BURG
3
5
NO
7
C
6
COM
9
NC
8
+12V
10
SIREN
+
SIREN
--
+–
12V
SIREN/SOUNDER**
ZONE
LOOP
PWR
GND
ZONE
16*
INPUT
+12V
GND
13
P3
4.7K OHM EOL RESISTOR
600-7630
(LOCATE AT
SUPERVISED SIREN
MODULE)
1A, 50V DIODE**
IN 4001 07-001
(LOCATE AT SIREN)
FIRE
ALARM
INTRU-
SION
ALARM
REGENCY MODEL 4720(A)
PANEL TERMINALS
REGENCY
MODEL 4180
STATUS
DISPLAY
MODULE
CONNECTOR
AND
TERMINAL
SUPERVISED SIREN
MODULE TERMINALS
* OR ANY ZONE INPUT PROGRAMED AS A
NORMALLY-OPEN SUPERVISORY INPUT.
56
10
** NOTE POLARITY.
38
- Installation Manual 1
- 2266 Second Street N orth 2
- FCC Notices 3
- Table of Contents 4
- List of Figures 7
- List of Tables 8
- Section 1: Introduction 9
- Section 2: UL Requirements 10
- Section 3: Installation 11
- MODEL 4720 12
- 3.2 Zone Expanders 13
- 3.3.1 Installation 14
- Section 4: Touchpad Operation 15
- 4.2 Touchpad Functions 16
- Section 5: Area Control 17
- 5.2 Area Assignments 18
- 7.1 Entering Program Mode 19
- 7.3 Programming the Options 19
- 7.4 Correcting Errors 20
- 7.5 Entering Text 20
- Table 2: Text and Characters 21
- 7.6 Programming Secret Codes 22
- 8457G15A.DS4 23
- 8.1 Time Windows (Menu 0) 24
- 8.2 Access (Menu 1) 25
- 8.3 Holidays (Menu 2) 27
- 8.5 System (Menu 4) 27
- Selection Default Mode 28
- “Exceptional” 31
- 8.6 Dialer (Menu 5) 35
- 8.7 Zone Options (Menu 6) 36
- Selection Loop Response Time 37
- TYPE#1:FIRE 39
- LOCATION#1 39
- SIL ALM#1:NO (Silent Alarm) 39
- REP. DLY#1:NO 39
- Table 7: Zone Types 39
- 8.8 Accounts (Menu 7) 40
- 8.9 Intercom (Menu 8) 42
- 8.10 Window Groups (Menu 9) 43
- 8.11 Messages (Menu 10) 43
- 8.12 Timers (Menu 11) 45
- Selection Day 46
- 8.13 Key Options (Menu 12) 47
- 8.14 Key Zones (Menu 13) 48
- 8.15 Area Options (Menu 14) 50
- 8.17.2 Program Operations 51
- Additional 52
- Info Needed 52
- 8.17.3 Changing the Program 56
- Inserting a New Statement 56
- Table 15: Default I/O Program 58
- 8.19 Code 0 and Code 1 59
- 9.1 Starting and Ending 59
- 9.2 Viewing Status 60
- 9.3 Uploading Event Memory 61
- 9.4 Programming Procedure 61
- Figure 5: Auxiliary Devices 62
- Table 16: Logical Operators 63
- Table 19: Output Designations 65
- Data Type Function 67
- Table 21: Zone Groups 69
- 11.1.1 Open/Close Groups 70
- 11.1.2 Exception Reporting 70
- 11.1.3 Open/Close Trouble 70
- 11.1.4 Auto Open/Close 70
- 11.2.1 New Programming Tools 70
- 11.3 New Options 71
- 11.4 Operational Changes 72
- Built-In Programmer 73
- Arm Delay 73
- Door Contact 73
- Entry Zones 73
- ONE YEAR LIMITED WARRANTY 74
- Numerics 75
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT 4720
Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT 4821 Instrucciones de operaciones
(48 paginas)
(48 paginas)
Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT INTELLIKNIGHT 5808 Manual de usuario
(8 paginas)
(8 paginas)
Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT INTELLIKNIGHT 5808 Especificaciones
(180 paginas)
(180 paginas)
Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT INTELLIKNIGHT 5808 Manual de usuario
(8 paginas)
(8 paginas)
Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT 5084 Manual de instalación
(58 paginas)
(58 paginas)
LG L216 manuals
Owner’s manuals and user’s guides for Unknown LG L216.
We providing 1 pdf manuals LG L216 for download free by document types: User Manual
Comentarios a estos manuales