SILENT KNIGHT 5700 Especificaciones Pagina 61
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Control Panel Installation
151295 4-33
4.14.3 NFPA 72 Polarity Reversal
4.14.3.1 Using the 5220 Module
When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble
events to a remote site. Alarms will override trouble conditions and it will not be possible to
reset the remote indicator until the condition is cleared and the control panel is reset.
If an alarm condition occurs, the alarm relay will close, overriding the trouble condition.
Standby Current: 100 mA
Alarm: 100 mA
Max. Voltage: 27.4 VDC
To install the 5220 for polarity reversal, follow the steps below:
1. Locate the knockout on the right side of the control panel cabinet to connect the 5220
using a short piece of conduit (must not exceed 20 feet in length).
2. Wire the 5220 to the control panel using the four-wire pigtail provided as shown in Figure
4-35. This diagram also shows how to connect the 5220 to the remote indicator. Do not
install an EOL resistor in the terminals of the NAC circuit used for this application.
3. Connect earth ground wire to the 5220 chassis with mounting screw.
4. Program the NAC circuit used as continuous and non-silencing. Refer to Section 7.5.1 for
zone grouping and mapping.
- INTELLIKNIGHT 1
- MODEL 5700 1
- Installation Procedure 3
- Contents 5
- Section 1 11
- Introduction 11
- 1.2 About this Manual 12
- 1.3 Compatible Products 13
- 1-4 151295 14
- 1-6 151295 16
- Section 2 17
- 2-2 151295 18
- 151295 2-3 19
- 2-4 151295 20
- Section 3 21
- Before You Begin Installing 21
- 3.3 Electrical Specifications 22
- 3.4 Wiring Specifications 23
- 3.5 Board Assembly Diagram 24
- 3.6.1 Worksheet Requirements 25
- 3-6 151295 26
- 3-8 151295 28
- Section 4 29
- Control Panel Installation 29
- 4.1.3.2 Dead Front Removal 30
- 4.2 AC Connection 31
- 4.3 Battery Connection 32
- 4.3.1 RBB Accessory Cabinet 33
- 4.4 SBUS Wiring 35
- 4-8 151295 36
- 4.4.2 Wiring Configurations 38
- 4.5.1 Mounting the 5860 40
- 4.5.1.1 Flush Mounting 41
- 4-14 151295 42
- 4.5.1.2 Surface Mounting 43
- Installation 44
- 4.6.1 Selecting 5824 Options 46
- 4.7 5880 LED Driver Module 47
- 4.7.2 FACP Connection 48
- 4.7.3 LED Wiring 49
- 4.7.4 Dry Contact Wiring 50
- 4.8.1 FACP Connection 51
- 4.8.2 5865 Mounting 52
- 4.9 Configuring Modules 53
- 4.10 Telephone Connection 54
- 4.11 5211 Ground Start Relay 54
- 4-28 151295 56
- 4.12.2.1 Door Holder Power 57
- 4.13.1 Common Trouble Relay 58
- 4.13.2 Programmable Relays 58
- 4-32 151295 60
- 4-34 151295 62
- 4-36 151295 64
- 4-38 151295 66
- Section 5 67
- SLC Device Installation 67
- 5.2 Maximum Number of Devices 68
- 5-4 151295 70
- 5.4 Wiring Detectors 71
- 5.5 Addressing Devices 72
- 5-8 151295 74
- Section 6 75
- Programming Overview 75
- 6.1.1 Input Points 76
- 6.1.2 Output Points 76
- 6.1.3 Running JumpStart 76
- 6.2 Mapping Overview 78
- 6.2.1 Input Point Mapping 79
- 6.2.2 Output Circuit Mapping 80
- 6.2.3 Zone Event Mapping 81
- 6-8 151295 82
- 6.2.4 Mapping LED Points 83
- Software Suite 84
- 6.4.4 Editing Keys 86
- 6-14 151295 88
- 6-16 151295 90
- 6-18 151295 92
- Section 7 93
- 7.2 Modules 94
- 7.2.2 Adding a Module 95
- 7.2.3 Deleting a Module 95
- 7.3 Zone 96
- 7.3.1.2 Edit Zone Properties 97
- Alarm Delay Characteristics 98
- 4. Press 98
- 7.3.1.3 Zone Outputs 99
- 7-8 151295 100
- Programming 101
- 7.3.1.4 Cadence Patterns 102
- 7.3.2 Add Zone 103
- 7.3.3 Delete Zone 103
- 7.3.4 View Zone Points 104
- 7.4 Group 105
- 7.4.1.2 Edit Group Properties 106
- 7.4.2 Add Group 108
- 7.4.3 Delete Group 109
- 7.4.4 View Group Points 109
- 7-18 151295 110
- 7.5 Point 111
- 7-20 151295 112
- Table 7-4: Point Programming 112
- 7-22 151295 114
- 7-24 151295 116
- 7.6 System Options 117
- 7.6.1.1 Edit Accounts 118
- 7.6.2 Phone Lines 120
- 7.6.2.1 Dialing Prefix 121
- 7.6.2.4 Rotary Format 122
- 7.6.2.5 Line Monitor 122
- 7.6.2.6 Ground Start Relay 122
- 7.6.3 Sys. Event Outputs 123
- 7.6.3.1 Trouble Events 124
- 7.6.3.2 System Alarm Cadence 125
- 7.6.4 Miscellaneous Options 1 126
- 7.6.4.2 Low AC Report Delay 127
- 7.6.5 Miscellaneous Options 2 128
- 7.6.6 Miscellaneous Options 3 129
- 7.6.7 Edit Banner Message 130
- 7.7 JumpStart Autoprogramming 131
- 7.8 Computer Account 132
- 7.9 Access Codes 133
- 7.9.1 Profile Edit Menu 134
- Section 8 135
- System Operation 135
- 8.2 Menu System 136
- 8.3 Basic Operation 137
- 8.3.3 View Event History 138
- 8.3.4 Conduct a Fire Drill 138
- 8.3.6 Conduct a Walk Test 139
- 8.3.7 Conduct a Dialer Test 140
- 8.3.9 Reset alarms 140
- 8.3.11 View Status of a Point 141
- 8.3.14 Reset dialer 141
- 8-8 151295 142
- 8.3.16 Working with a Printer 143
- 8.4 Operation Mode Behavior 144
- 8.5 Releasing Operations 146
- 8-14 151295 148
- 8.6 Smoke Alarm Verification 149
- 8-16 151295 150
- Section 9 151
- Reporting 151
- Zone Events 152
- Section 10 155
- Testing and Troubleshooting 155
- 10.2.1 Event History 156
- 10.3.1 SLC Device Locator 157
- 10.3.2 SLC Multi Locator 158
- 10.3.3 I/O Point Control 159
- 10-6 151295 160
- Section 11 161
- Installation Records 161
- 11-2 151295 162
- Appendix A 163
- Compatible Devices 163
- A-2 151295 164
- A-6 151295 168
- System Sensor 168
- A-8 151295 170
- Wheelock 170
- A-10 151295 172
- A-12 151295 174
- A.2 Door Holder Device 175
- A.3 Two-Wire Smoke Detectors 176
- A-16 151295 178
- Appendix B 179
- Special Characters Lists 179
- B-2 151295 180
- Cut Along the Dotted Line 183
- Acknowledge 183
- © 2006 Silent Knight 186
© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales