SILENT KNIGHT 4821 Manual de instalación Pagina 70
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Model 4821/4820 Control/Communicator Installation Manual
4-26 150964
4.16 Smoke Detector Wiring and Operation
Note: The Model 4821/4820 is not compatible with 2-wire smoke detectors.
4.16.1 Smoke Detector Compatibility
This section describes the 4821/4820 reset and smoke verification cycles. Any smoke detec-
tors attached to the 4821/4820 must be compatible with the reset cycle. If you are using the
smoke verification feature, smoke detectors must also be compatible with the smoke verifica-
tion cycle. See Section 4.16.1.1 for information about reset operation. See Section 6.3.2.3 for
information about programming the smoke verification option.
4.16.1.1 Smoke Reset Cycle
When you reset a smoke detector, power is off for 6 seconds. The system then applies a restart
time of 36 seconds. During the restart time, smoke power is reapplied and the zones are
allowed to stabilize. The system will not respond to fire zones during the reset period (but will
respond to other types of zones, including fire contact zones).
4.16.1.2 Smoke Verification Cycle
Smoke verification is a four-period cycle:
• Retard Period 18 second delay after a zone is tripped before smoke detector power
turns off.
• Reset Period Smoke detector power is off for 6 seconds.
• Restart Period 36 seconds for the smoke detectors to stabilize. The system will not
respond to fire zones during this time (but will respond to other
types of zones, including fire contact zones).
• Confirmation Period 60 second period during which all zones will be considered instant.
If the zone trips a second time during this period, the zone will go
into alarm immediately.
Smoke verification will not occur if any fire zones are currently in alarm anywhere in the
same partition.
Note: Smoke verification is not compatible with the 10 second zone response (debounce) speed. See Section
6.3.2.3 for more information.
- Contents 1
- Section 3 2
- Section 4 2
- Section 5 4
- Section 6 5
- Troubleshooting 6
- Section 1 7
- Introduction 7
- 1.1.1 Compatible Modules 8
- 1-4 150961 10
- 1.2 How to Use this Manual 11
- 1.4 Agency Requirements 12
- 1.4.3 UL Requirements 13
- 1.4.3.2 Grade A Mercantile 14
- 1.4.3.4 Access Control UL-294 15
- 1-10 150961 16
- Section 2 17
- Quick Start 17
- 2-2 150962 18
- 2.2 Sending Data to the Panel 19
- 2.4 Installation Records 20
- 2.4.1.1 Zone Record 22
- 4815 Expander Loop2 25
- 2-10 150962 26
- 3-2 150963 28
- 150963 3-3 29
- 3-4 150963 30
- 3.2.2 Mounting 31
- 3-6 150963 32
- 150963 3-7 33
- 3-8 150963 34
- 150963 3-9 35
- 3.4 Access Control Operation 36
- 3.4.2 End-User Operation 37
- 3.4.4 Viewing Door Status 38
- 3.4.5 Anti-Passback Feature 39
- 3-14 150963 40
- 150963 3-15 41
- 3-16 150963 42
- 150963 3-17 43
- 3-18 150963 44
- 4.3 Board Layout 46
- 150964 4-3 47
- 4.5 Power Limiting Circuits 48
- 4.6 Power Switch 49
- 4.8 Wire Routing 50
- 4.9 Current Draw Worksheets 51
- 4-8 150964 52
- 150964 4-9 53
- 4-10 150964 54
- 150964 4-11 55
- 4.10 AC Power Transformer 56
- 150964 4-13 57
- 4-14 150964 58
- 4.13 SBUS 59
- 4-16 150964 60
- Max. Distance = 500V 61
- 4.14 Touchpad Installation 62
- 4.14.3 Wiring Touchpads 63
- 4.15 Zone Installation 64
- 4.15.3 Zone Configuration 65
- 4-22 150964 66
- 150964 4-23 67
- 4-24 150964 68
- 150964 4-25 69
- 4.16.1.1 Smoke Reset Cycle 70
- 150964 4-27 71
- 4.17 Speaker Wiring 72
- 4.18 Bell Wiring 73
- 4.18.2 Commercial Bell Wiring 74
- 4.19 4884 Bell Module wiring 75
- 4-32 150964 76
- 150964 4-33 77
- 4.21 Built-in Relay 78
- 4.22 DACT Compliant Wiring 79
- Alarm Relay Trouble Relay 80
- 150964 4-37 81
- 4-38 150964 82
- 5-2 150965 84
- 5.2 Touchpad Models 86
- 6LOHQW.QL 87
- 5.3.2 Normal Display Messages 88
- 5.3.3 System Status Messages 88
- 5.4 Touchpad Buttons 89
- 5-8 150965 90
- 5.6 Interactive Menu Overview 91
- 5.7 System Operation Summary 92
- 5-12 150965 94
- 5-14 150965 96
- 5.9 System Test Descriptions 98
- 5-18 150965 100
- System Operation 101
- 5-20 150965 102
- MUTE-Exit Menu 103
- [Installer’s Code] 104
- 6.2.2.1 1-Install Device 105
- 6.2.2.2 2-Edit System Options 105
- 6.2.2.3 3-Edit Partition 106
- 6.2.2.4 4-Edit Ph. Lines 106
- 6.2.2.5 5-Reprt Accounts 107
- 6.2.2.6 6-Print Accounts 107
- 6.2.2.7 7-Edit Profiles 108
- Programming 109
- 6-8 150966 110
- 6.2.2.9 8-Edit Schedules 111
- 6.2.2.10 9-Delete Options 112
- 6.3 Programmable Options 113
- 6-12 150966 114
- 6.3.1.2 Dialer Screen 116
- 6.3.1.3 Devices Screen 117
- 6-16 150966 118
- 6-18 150966 120
- 6-20 150966 122
- 6-22 150966 124
- 6.3.2.3 Zones Screen 125
- 6-24 150966 126
- 6-26 150966 128
- 6-28 150966 130
- 6.3.2.5 Areas Screen 132
- 6.3.3 Time Schedules Screen 133
- 6.3.4 Universal Schedules 134
- 6.3.5 User Profiles Screen 135
- 6.3.6 Users Screen 136
- Section 7 137
- Reportin 137
- 7.2 SIA Event Codes 138
- Reporting 139
- 7-4 150967 140
- 3 = Restore event 142
- 7-8 150967 144
- Open-Close 146
- 7-12 150967 148
- Alarm Restore 149
- Alarm Rese 149
- Door Access 149
- Exception OPCL 150
- Trouble OPCL 150
- Door Access Denied 151
- Door Exit 151
- Door Left Open 151
- 7-16 150967 152
- Section 8 153
- Troubleshootin 153
- 8-2 150968 154
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad SILENT KNIGHT 4821
(186 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales